- Studio Condenser Microphone Recording Pack
- How To Connect Mic To Fl Studio 12 Without The Delay
- How To Connect Mic To Fl Studio 12
Unlimited resources fallout 4. Assigning tracks to the mixer in FL Studio on Youtube
Assigning tracks to the mixer in FL Studio
Assigning tracks to the FL Studio mixer is an essential task you will need to know. The FL studio mixer is a key component to getting good sounding beats. The FL Studio mixer is where you will add effects to your channels and tracks. This may include compression, EQ, limiting, reverb, delay, and much more. In order to use it effectively you will need to assign channels to the mixer. In this tutorial we show you a couple different ways to do this. One way will show you how to put your different channels and instruments on there own mixer tracks for further processing. The next way will show you how to assign multiple channels for one mixer channel.
![Connect Connect](/uploads/1/2/3/7/123704197/500026326.jpg)
Assigning tracks to the FL Studio mixer
Assigning tracks to the FL studio mixer is a pretty simple yet very effective task. In the channel window there is a green LED next to each channel (when selected). In order to send tracks to the mixer the LED needs to be green. To activate it you can either left or right click. Left click allows you to activate one channel while right clicking will allow you to activate multiple channels. In this tutorial right click was used in order to send multiple tracks to the mixer at one time.
Once you have the LED lit for each track that you want to send to the mixer, open the mixer. This can be done under the view menu in FL Studio. Once the mixer is open click on the first available mixer slot you would like to assign channels to. Right click on the available slot and choose Link selected channels, starting from this track. This method will assign each channel that is selected to its own mixer track for processing. If you want to route multiple channels to the same mixer track for similar processing right click on an available mixer slot, choose link selected channels, to this track.
Related posts:
You can use a headphone jack to provide audio for recording. Since a headphone jack gives a line-level audio source, the recording will not be amplified, so you may need to boost the volume after the recording is done through your mixing tools. Standard 1/4-inch and 1/8-inch headphone jacks provide a stereo signal through a tip, ring and sleeve connection. The stereo output may not be received by all recording devices. The same tip, ring and sleeve connection for a microphone line-in typically only reads one channel of audio.
Step 1
Connect the adapter to the headphone jack. The most common situation will be an 1/8-inch male-to-male adapter so that you can plug the headphone jack on a computer into the microphone jack on a computer. However, if you're using different audio equipment, you might need an adapter from 1/8-inch to 1/4-inch that is used for instrument line-in on most sound boards or from 1/8-inch to XLR with is the microphone input on most sound boards. The recording inputs on a home stereo system will be the red and white RCA connectors.
Step 2
Plug the mic cable into the adapter and into the recording device. When you do this, you want both the recording device and the playback device to be powered off to prevent any spike in sound during the connection. This is especially important when you are running a live audio recording as the connection will pop over the speakers.
Step 3
Set the volume for the headphone jack to be 50 percent. Allow the recording device to account for the low volume after the fact. If the volume is too high on the headphone jack it might introduce distortion into the recording. It's always easier to increase the volume later than remove distortion from a recording.
Step 4
Test the input by playing the audio on the device with the headphone jack. If you have monitors or a speaker attached to your recording device, set the volume level to about 20 percent. Adjust the volume for the recording by increasing or decreasing the gain level of the input, not the master volume. On a sound board, the gain knob is typically the top knob on the row associated with that source. Excel image assistant cracked windows 10. On a computer, the gain is the microphone input level, not the computer's speaker volume.
Stop the device with the headphone jack. Start the recording on the device with the microphone line-in and the re-start the audio on the device with the headphone jack. Don't adjust the volume on the output device or the gain on the recording device until the recording is over.
Studio Condenser Microphone Recording Pack
![How To Connect Mic To Fl Studio How To Connect Mic To Fl Studio](/uploads/1/2/3/7/123704197/222729633.jpg)
Items you will need
- Converter from 1/4 or 1/8 inch headphone output to microphone input
Video of the Day
How To Connect Mic To Fl Studio 12 Without The Delay
Brought to you by Techwalla
How To Connect Mic To Fl Studio 12
- Jupiterimages/Photos.com/Getty Images